makerbot replicator 2 spool holder 3d models

If you prefer, flatten the bottom of the screw post and attach an adhesive rubber foot to prevent your MakerBot from walking across the table. I've added a small hook spanner wrench to make setting the feet simpler. ...It should be printed with two...

... ensuring to set the HBP temperature accordingly (115°C for T0). Adding Kapton tape under fans and taping paper on makerbot sides can help retain heat during printing. ...A useful reference is wiki.bitsfrombytes.com/index.php?title=Skeinforge_Raft.

To stop the filament from unspooling and winding around the spool holder between my Replicator and the spool, I made this clip to hold the filament away from the back of the case. It seems to work really well for me and appears to be doing a good job...

... The latest update brings enhanced stress relief on the lever while providing better access to the hot end. ...Printing the fan holder in ABS is a necessity. Your feedback matters! Share your thoughts with us. ... Warm regards, JavoPinch-FABLAB UCHILE

This set contains:\nVernier Calipers\nFeeler Gauges\nNozzle Spanner (7mm wrench)\nHex Keys - 1.5, 2, 2.5, 5mm\nScraper\nSmall side cutters (mine are ~15.8x 7.8mm head)\nSmall brush\nSmall flathead screwdriver - widest around 8mm\nTweezers\n2x SD...

I suggest using helper disks via Makerware and McMaster-Carr hardware like M6 x 16 mm flange-head socket cap screws (#92235A238), 3x 3/8 x 2' threaded rod (#98804A031) for holding supports and guiding filament, 3/8 hex nuts (any will do) to hold the...

This iPhone holder is ideal for your Replicator 2, allowing you to capture excellent timelapse videos of your prints without compromising stability. Printed using a 0.3mm layer height and 10% infill on standard Makerware settings, it's easy to print...

I designed this part to address a common issue with the Replicator 2x, where cable breakage often occurs when transitioning from dual extruders to the wiring harness. This upgrade allows for a longer cable run, secured by three cable ties. Printing...

Designed Specifically from http://www.thingiverse.com/thing:44906 by User Customization Made Using Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=44906 Design Information Options Selected: - spool_width is set to 100 units -...

... of http://www.thingiverse.com/thing:44906 was made using the Customizer app at http://www.thingiverse.com/apps/customizer/run?thing_id=44906. ...The customization involved setting the unit to 1, the spool hole diameter to 30, and the spool width to 90.

... to life! **Spinning Fun** Using these settings: Unit Size: 1 unit is set at standard. Width: I chose 72.5, let's get precise! Hole Diameter: Let's fit a spool that's perfect with 32 mm! ... **That's it, start creating and customize now!**

I tried a few other 30 x 100 spool holder designs, but I needed something that printed as a single part, was specifically designed for the Replicator 2, made it simple to load and unload spools and held them firmly in place. UPDATE If you're...

In quest of a simple one-piece substitute for the intricate and tricky MakerBot spool holders, I stumbled upon whpthomas's exceptional design; however, it was slightly too long for my MakerBot space. To resolve this issue, I limited the spool length...

This text is a description of a 3D-printed spool holder for the Replicator 2 that offers improved design features compared to other available options. The new version (wRafts) addresses issues with corner lifting by adding tear-off ear rafts to...

... apply CA glue to one side, and clamp until the glue cures for enhanced stability. Note that the STL file includes 2.1 clearance holes for 2.0mm pins; however, they may print smaller on a MakerBot, so you can use 1.5mm spring pins instead. ...Enjoy!

The model was sliced at 2 shells, 15% infill, and 0.3mm layer height in Makerware, built on Replicator 2. Remove popout tabs for installation. I had to adjust a zip-tie due to interference, but it's centered now. ...Wishing you success with your build!

Needed something to bring a little organisation and order into my printing kit; so I designed this, a gluestick holder (will suit any gluestick with a diameter of 31.5mm or less). ... *** Print upside down with supports for best results!

The spool holder inserts aren't necessary, but they let the spools spin more freely. If you're curious about the PVC paint, I used Rust-oleum Metallic Flat Soft Iron. I prefer Rust-oleum for all spray painting jobs. To make this design, you'll need...

Spool holder for the CTC Bizer or the Makerbot Replicator

Customized version of https://www.thingiverse.com/thing:2247908 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2247908 Instructions Using the following options: spool_width = 66 unit = 2 spool_hole_diameter = 20

I've recently found several filament suppliers shipping a compact spool along with their 1 Kg of filament, approximately measuring 90 mm x 160 mm in size, featuring a 35/30 mm diameter hole that fits nowhere near the standard spool holder found in...

To declutter my workspace, I replicated a design (http://www.thingiverse.com/thing:51635) but made adjustments for lighter weight and faster printing, along with improved aesthetics. The 3/8-inch SS rod, available at Home Depot or McMaster.com,...

This redesign is based on the original spool holder (http://www.thingiverse.com/thing:74050) and serves as an upgrade. The MatterHackers Pro series spools have smaller centers at 0.75in diameter, which wouldn't fit previous designs due to width...

Using the original spool holder works, but it's janky and it creates horrible amounts of friction with cardboard spools, and spools that have a nick or filament tail inside will hang up on the slot and jam. This holder uses a wingnut and a felt or...

Customized version of http://www.thingiverse.com/thing:44906 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44906 Instructions Using the following options: unit = 1 spool_width = 130 spool_hole_diameter = 30

... I decided to fine-tune it for my Octave 1kg ABS spools. This adjustment was unnecessary since the previous version functioned perfectly as well. For customization, unit = 1, spool_hole_diameter = 32, and spool_width = 100 were used.

... Customizer! ...You can access it at http://www.thingiverse.com/apps/customizer/run?thing_id=44906. For this personalized print, the spool hole diameter is set to 30 and the unit of measurement is 1. ...Additionally, the spool width is specified as 100.

... at http://www.thingiverse.com/apps/customizer/run?thing_id=44906. For this specific design, the spool width is set to 100 and the spool hole diameter to 30, with units in millimeters. ...Follow these instructions to complete your customized print.

A customized version of http://www.thingiverse.com/thing:44906 has been created using the Customizer with specifications of spool hole diameter as 27, spool width as 80, and unit measurement as 1. ...The instructions for this customized design can be...

This is a customized version of the model found at http://www.thingiverse.com/thing:44906, created using the Customizer app with the settings spool hole diameter of 30mm, unit size of 1, and spool width of 95mm. ...For instructions on how to use these...